上海南汇区聚氨酯水泥砂浆地坪装饰施工价格

上海南汇区聚氨酯水泥砂浆厂房地坪装饰施工价格 因为施工环氧地坪漆期间部分机组正在装置,为确保施工人员的身心健康以及防止新装置的机组遭到粉尘污染,选用无尘研磨机进行无尘研磨,有效地防止粉尘污染环境及厂房内设备。打磨时将混凝土外表的水泥净浆,单薄层,油污等铲除,并将凸起部位打磨平坦,直至显露无缺,坚固,密实的混凝土外表。 混凝土基面打磨后,用2m靠尺对基面进行检查,对基面存在的孔洞,低洼部位作出符号,并用快硬高强修补砂浆进行添补,使整块混凝土外表根本处于同一水平面。五颜六色地上强化料第二遍 当在镘抹撒有五颜六色强化料的混凝土外表时,假如还有过多的泌水或色彩较浅的当地,再均匀撒一层五颜六色强化料。第二遍抛撒的方向应与靠前次的方向笔直。一起,应依据不同施工现场的情况,如混凝土的初凝时刻等,进行恰当的调整。第二遍用量约为总用量的30%. 4,五颜六色地上强化料第三遍联络:4oo-o7o9-91o 当第二遍五颜六色强化料以抹均匀并充沛湿润后,如部分当地还呈现深浅不匀或难以掩盖(如淡色强化料系列),则再进行第三次撒粉,此次撒粉方向可有的放矢进行,首要依据外表实践深浅情况进行修补,并再用铁镘子细心镘均匀。第三遍用量约为总量的20%~30%. 5,五颜六色脱膜粉 地坪外表资料在初凝后用手按过,可呈现明晰手纹时。即可如前述抛撒五颜六色地上强化料相同,在地坪的外表均匀抛撒欧进五颜六色脱模粉,将整个外表掩盖。 6,压花施工 从一个边际开端,排放靠前块模板,施工人员用夯实器或人站在压模板上均匀将分量传递到混凝土外表上。将模板上的纹路压印在混凝土的外表,然后将第二块模板紧靠在靠前块模板的边际,如前所述,夯压模板。当压模板悉数放在混凝土上时。将靠前块模板拿起,放在较后一块模板边上,重复以上夯压次序,直到完结整个外表的纹路压印。压模时应确保一切模板的顶面齐平,以确保压印纹路的深度一致;脱模时,应笔直拿起,否则会危害已压印的纹路。在压纹进程中如遇到墙柱等障碍物,硬模板不适用时,应选用软压模板,压纹办法仍同前述。如压印的勾缝有不自然时,用勾缝东西进行修补。 基面处理完毕后,机械设备及不做地坪的部位四周平直张贴泡沫胶带,防止地坪施工时资料溢出作业区,以确保地坪边际规整。4.2关闭底漆施工关闭底漆刮涂之前,将施工区域内地板,边墙以及机器设备等进行完全清洁处理,确保施工区域不存留浮灰。将按份额制造并搅拌均匀的关闭底漆资料用刮板涂刮在混凝土基面上,涂刮时留意不能太薄,速度也不能过快,确保施工进程中有满足量的资料在混凝土内部进行浸透以及有充沛的浸透时刻。别的,还要坚持涂刮的连续性,防止呈现漏刮现象。4.3中层腻子涂刮用刮板将搅拌均匀的腻子涂刮在固化并洁清的混凝土基面上,涂刮腻子遵从的原则是将整个基面掩盖,不露底,关于部分低洼部位要满足的涂刮厚度,确保整个基面根本平齐。Due to the epoxy floor paint construction during part of the unit is installed, in order to ensure the physical and mental health of the construction workers and prevent newly installed units were polluted by dust, dust free grinding by a dust-free grinding machine, effectively prevent the dust pollution of the environment and plant equipment. When grinding the concrete surface of the cement paste, weak, oil and other clear, and the convex parts of the smooth, until the exposed intact, hard, dense concrete surface.Concrete surface after grinding, with 2m by foot on the surface of the base are examined, to surface in the presence of holes, the low-lying parts make markings and fast hardening and high strength mortar fill, causes the entire surface of the concrete in the same horizontal plane. Color ground reinforcement second timesWhen in trowel wipe sprinkle color reinforced concrete surface, if had excessive bleeding or lighter in color, and then evenly sprinkle a layer of color reinforced material. Second times the direction of the scatter should be perpendicular to the direction of the first. At the same time, according to the situation of different construction site, such as the initial setting time of concrete, appropriate adjustments. Second times the amount of about of the total amount of 30%.4, color ground reinforced material third times contact: 4oo-o7o9-91oWhen the second times color strengthening material to evenly and fully wet, such as local also appeared the uneven depth or difficult to cover (such as light strengthening material series), and then the third dredge, the direction of the dusting can be targeted, mainly according to the actual status of the depth of the surface for repair, and then iron trowel carefully uniform trowel. Third times the amount of about of the total amount of5, color filmThe surface of floor material after the initial setting by hand, there may be a clear hand when. Can such as the aforementioned throwing colored floor strengthening material as, in the floor surface uniformly throwing Saou into color stripping powder, covering the entire surface.6, embossing constructionFrom an edge, the first discharge of the template, the construction personnel with a solid device or people standing on the press template will be evenly transferred to the weight of the concrete surface. The texture of the template on the surface of the concrete, and then the second template close to the edge of the first template, as previously mentioned, the ram pressure template. When all the pressure is placed on the concrete. Pick up the first template and place it on the edge of the last piece of the template, and repeat the order until the entire surface is pressed. When the die should be to ensure that all the top surface of the template, in order to ensure the depth of the imprint lithography uniform; release, should be picked up vertically, otherwise it will damage the already embossed texture. In the embossing process, such as the wall column and other obstacles, the hard template does not apply, should be a soft template, the compression method is still the same. If there is not a natural pointing imprint, repaired by pointing tool.After treatment of base, mechanical equipment and without the floor around the site straight paste foam tape, to prevent floor construction material overflow operation area, to ensure the neatness of the edge of the floor.4.2 closed primer constructionSealer scraping before, the construction area of floor, wall and machinery equipment and a thorough cleaning, ensure construction area is not kept floating dust.Will be according to the proportion of preparation and mixing evenly the sealer material with coating scraper scraping on the concrete surface coated with scraping careful not too thin, speed is not too fast, to ensure construction process in a sufficient amount of material in the interior of the concrete of penetration and full penetration time. In addition, but also to maintain the continuity of the wiper, to avoid leakage phenomenon.4.3 middle putty scrapingWith a scraper be uniform mixing of putty scraping in curing and clean concrete surface, scraping putty follow the principle is to cover the whole surface, grinning, for the local low-lying parts to enough scraping thickness to ensure the whole surface of basic flush.